Rob's /sun/sun4u/ Image Archive
LOMlite starting up.

CPU type: H8/3437S, mode 3
Ram-test: 2048 bytes OK
Initialising i2c bus: OK
Searching for EEPROMs: 50(cfg)
I2c eeprom @50: OK
i2c bus speed code 01... OK
Clearing the LOM event log... done
Probing for lm80s: 28
Initialising lm80 @28: OK
Probing for lm75s: none
System functions: PSUs fans breakers rails gpio temps host CLI ebus clock

LOMlite console
lom>
LOM event: +0h0m0s LOM booted
lom>help
The following commands are supported:
alarmon
alarmoff
check
console
environment
faulton
faultoff
help
poweron
poweroff
reset
shutdown
show
version
set
break
bootmode
loghistory
showlogs
consolehistory
chist
date
showdate
logout
userpassword
useradd
userdel
userperm
usershow

lom>env 
Fault  OFF
Alarm1 OFF
Alarm2 OFF
Alarm3 ON
   
Fans:
1 fan1 OK speed 100%
2 fan2 OK speed 100%
3 cpu OK speed 100%
4 psu OK speed 100%

PSUs:
1 OK

Temperature sensors:
1 Enclosure 34degC OK
1 Enclosure 29degC OK

Overheat sensors:
1 CPU OK 

Circuit breakers:
1 SCSI-Term OK
2 USB0 OK
3 USB1 OK
4 SCC OK

Supply rails:
1 5V OK
2 3V3 OK
3 +12V OK
4 -12V OK
5 CPU core OK
6 +3VSB OK
lom>poweron
LOM event: +0h0m46s host power on
|




Processor Speed = 648 MHz
Baud rate is 9600
8 Data bits, 1 stop bits, no parity (configured from lom)

Firmware CORE  Sun Microsystems, Inc.
@(#) core 1.0.12 2002/01/08 13:00
Software Power ON
Verifying NVRAM...Done
Bootmode is 0
[New I2C DIMM address]
MCR0 = 57b2ce06
MCR1 = 80008000
MCR2 = cff0bbbf
MCR3 = a00003ff
Ecache Size = 512 KB
Clearing E$ Tags Done
Clearing I/D TLBs Done
Probing memory
Done
MEMBASE=0xc0000000
MEMSIZE=0x10000000
Clearing memory...Done
Turning ON MMUs Done
Copy ROM to RAM (170040 bytes) Done
Orig PC=0x1fff0007e44  New PC=0xf0f07e9c
Processor Speed=648MHz
Looking for Dropin FVM ... found
Decompressing Client Done
Transferring control to Client...

ttya initialized
Reset Control: BXIR:0 BPOR:0 SXIR:0 SPOR:1 POR:0 
Probing upa at 1f,0 pci pci pci 
Probing upa at 0,0 SUNW,UltraSPARC-IIe SUNW,UltraSPARC-IIe (512 Kb)
Loading Support Packages: kbd-translator 
Loading onboard drivers: ebus flashprom eeprom idprom SUNW,lomh 
Probing /pci@1,1 Device 3  pmu i2c temperature dimm dimm dimm dimm 
   i2c-nvram idprom motherboard-fru fan-control 
lomp 
Probing Memory Bank #0 512 Megabytes
Probing Memory Bank #1 256 Megabytes
Probing Memory Bank #2 256 Megabytes
Probing Memory Bank #3 256 Megabytes
Probing /pci@1,1 Device 7  isa power serial serial 
Probing /pci@1,1 Device c  network firewire usb 
Probing /pci@1,1 Device 3  
Probing /pci@1,1 Device d  ide disk cdrom 
Probing /pci@1,1 Device 5  pci108e,1100 network firewire usb 
Probing /pci@1 Device 8  scsi disk tape scsi disk tape 
Probing /pci@1 Device 5  Nothing there 
Probing /pci@1 Device 6  Nothing there 
Probing /pci@1 Device 7  Nothing there 
Sun Fire V120 (UltraSPARC-IIe 648MHz), No Keyboard
OpenBoot 4.0, 1280 MB memory installed, Serial #51495413.
Ethernet address 0:3:ba:11:c1:f5, Host ID: 8311c1f5.


Environment monitoring: disabled
Executing last command: boot                                          
Boot device: disk  File and args: -v
Loading ufs-file-system package 1.4 04 Aug 1995 13:02:54. 
FCode UFS Reader 1.12 00/07/17 15:48:16. 
Loading: /platform/SUNW,UltraAX-i2/ufsboot
Loading: /platform/sun4u/ufsboot
Size: 571d9+144b2+0x24542 Bytes
SunOS Release 5.9 Version Generic_112233-01 64-bit
Copyright 1983-2002 Sun Microsystems, Inc.  All rights reserved.
Use is subject to license terms.
Ethernet address = 0:3:ba:11:c1:f5
mem = 1310720K (0x50000000)
avail mem = 1274855424
root nexus = Sun Fire V120 (UltraSPARC-IIe 648MHz)
pcipsy0 at root: UPA 0x1f 0x0
pcipsy0 is /pci@1f,0
PCI-device: pci@1,1, simba0
simba0 is /pci@1f,0/pci@1,1
PCI-device: pci@1, simba1
simba1 is /pci@1f,0/pci@1
/pci@1f,0/pci@1/scsi@8 (glm0):
        glm0 supports power management.
/pci@1f,0/pci@1/scsi@8 (glm0):
        Rev. 7 Symbios 53c896 found.
PCI-device: scsi@8, glm0
glm0 is /pci@1f,0/pci@1/scsi@8
/pci@1f,0/pci@1/scsi@8,1 (glm1):
        glm1 supports power management.
/pci@1f,0/pci@1/scsi@8,1 (glm1):
        Rev. 7 Symbios 53c896 found.
PCI-device: scsi@8,1, glm1
glm1 is /pci@1f,0/pci@1/scsi@8,1
PCI-device: ide@d, uata0
uata0 is /pci@1f,0/pci@1,1/ide@d
sd0 at glm0: target 0 lun 0
sd0 is /pci@1f,0/pci@1/scsi@8/sd@0,0
sd30 at uata0: target 0 lun 0
sd30 is /pci@1f,0/pci@1,1/ide@d/sd@0,0
sd1 at glm0: target 1 lun 0
sd1 is /pci@1f,0/pci@1/scsi@8/sd@1,0
root on /pci@1f,0/pci@1/scsi@8/disk@0,0:a fstype ufs
PCI-device: ebus@c, ebus0
ebus0 is /pci@1f,0/pci@1,1/ebus@c
PCI-device: isa@7, ebus1
ebus1 is /pci@1f,0/pci@1,1/isa@7
su0 at ebus1: offset 0,3f8
su0 is /pci@1f,0/pci@1,1/isa@7/serial@0,3f8
su1 at ebus1: offset 0,2e8
su1 is /pci@1f,0/pci@1,1/isa@7/serial@0,2e8
cpu0: SUNW,UltraSPARC-IIe (upaid 0 impl 0x13 ver 0x33 clock 648 MHz)
PCI-device: usb@c,3, ohci0
ohci0 is /pci@1f,0/pci@1,1/usb@c,3
PCI-device: usb@5,3, ohci1
ohci1 is /pci@1f,0/pci@1,1/usb@5,3
SUNW,eri0 : Local Ethernet address = 0:3:ba:11:c1:f5
PCI-device: network@c,1, eri0
eri0 is /pci@1f,0/pci@1,1/network@c,1
SUNW,eri1 : Local Ethernet address = 0:3:ba:11:c1:f6
PCI-device: network@5,1, eri1
eri1 is /pci@1f,0/pci@1,1/network@5,1
configuring IPv4 interfaces: eri0 eri0:60 eri0:61 eri0:62 eri0:63 eri0:64 eri0:65 eri0:66 eri0:67 eri0:68 eri0:69 eri0:70 eri0:71 eri0:72 eri0:73 eri0:74 eri0:75 eri0:76 eri0:77 eri0:78 eri0:79 eri0:80 eri0:81 eri0:82 eri0:83 eri0:84 eri0:85 eri0:86 eri1.
Hostname: rob
dump on /dev/dsk/c1t0d0s1 size 2047 MB
Configuring /dev and /devices
pseudo-device: devinfo0
devinfo0 is /pseudo/devinfo@0
SUNW,eri0 : 100 Mbps full duplex link up
SUNW,eri1 : 100 Mbps full duplex link up
pseudo-device: fssnap0
fssnap0 is /pseudo/fssnap@0
pseudo-device: winlock0
winlock0 is /pseudo/winlock@0
pseudo-device: lockstat0
lockstat0 is /pseudo/lockstat@0
pseudo-device: vol0
vol0 is /pseudo/vol@0
pseudo-device: llc10
llc10 is /pseudo/llc1@0
pseudo-device: pm0
pm0 is /pseudo/pm@0
pseudo-device: tod0
tod0 is /pseudo/tod@0
power0 at ebus1: offset 0,2000
power0 is /pci@1f,0/pci@1,1/isa@7/power@0,2000
pseudo-device: lofi0
lofi0 is /pseudo/lofi@0
pseudo-device: fcp0
fcp0 is /pseudo/fcp@0
pseudo-device: rsm0
rsm0 is /pseudo/rsm@0
pseudo-device: trapstat0
trapstat0 is /pseudo/trapstat@0
PCI-device: lomp@3, lomp0
lomp0 is /pci@1f,0/pci@1,1/lomp@3
lom0 at ebus0: offset 14,200000
lom0 is /pci@1f,0/pci@1,1/ebus@c/SUNW,lomh@14,200000
9/24/2002 17:8:17 GMT LOM time reference
Configuring the /dev directory (compatibility devices)
The system is coming up.  Please wait.
/dev/rdsk/c0t0d0s2 uncorrectable error
checking ufs filesystems
/dev/rdsk/c1t1d0s7: is clean.
/dev/rdsk/c1t1d0s6: is clean.
/dev/rdsk/c1t1d0s0: is clean.
Sep 24 13:08:22 su: 'su sys' succeeded for root on /dev/console
loading skip keystore.
starting skip key manager daemon.
starting rpc services: rpcbind done.
starting internet domain name server.
Setting default IPv4 interface for multicast: add net 224.0/4: gateway rob
syslog service starting.
Starting CommuniGate Pro
Starting Sophie Anti-Virus daemon: 
Sep 24 13:21:35 rob sophie[392]: Initializing  : Sophos engine version 2.10
Sep 24 13:21:35 rob sophie[392]: Initializing  : Sophos IDE version 3.61 (detects 76015 viruses)
Sep 24 13:21:35 rob sophie[392]: Socket path   : "/var/run/sophie"
/usr/local/bin/sophie virus scanning daemon started
Sep 24 13:21:35 rob sophie[392]: /usr/local/bin/sophie virus scanning daemon started [PID: 394]
Log directory = .

Initializing Network Interface eri1

        --== Initializing Snort ==--
Decoding Ethernet on interface eri1
Initializing Preprocessors!
Initializing Plug-ins!
Initializating Output Plugins!
Parsing Rules file /opt/snort/etc/snort.conf

+++++++++++++++++++++++++++++++++++++++++++++++++++
Initializing rule chains...
No arguments to frag2 directive, setting defaults to:
    Fragment timeout: 60 seconds
    Fragment memory cap: 4194304 bytes
    Fragment min_ttl:   0
    Fragment ttl_limit: 5
    Fragment Problems: 0
Stream4 config:
    Stateful inspection: ACTIVE
    Session statistics: INACTIVE
    Session timeout: 30 seconds
    Session memory cap: 8388608 bytes
    State alerts: INACTIVE
    Evasion alerts: INACTIVE
    Scan alerts: ACTIVE
    Log Flushed Streams: INACTIVE
    MinTTL: 1
    TTL Limit: 5
No arguments to stream4_reassemble, setting defaults:
     Reassemble client: ACTIVE
     Reassemble server: INACTIVE
     Reassemble ports: 21 23 25 53 80 143 110 111 513
     Reassembly alerts: ACTIVE
     Reassembly method: FAVOR_OLD
Rob stuff done
The system is ready.
1476 Snort rules read...
1476 Option Chains linked into 189 Chain Headers
0 Dynamic rules
+++++++++++++++++++++++++++++++++++++++++++++++++++

Rule application order: ->activation->dynamic->alert->pass->log

        --== Initialization Complete ==--

-*> Snort! <*-
Version 1.8.7 (Build 128)
By Martin Roesch (roesch@sourcefire.com, www.snort.org)

rob console login: 
Sep 24 13:22:24 rob su: 'su root' succeeded for rob on /dev/pts/1
Sep 24 13:26:24 rob pseudo: pseudo-device: devinfo0
Sep 24 13:26:24 rob genunix: devinfo0 is /pseudo/devinfo@0

       0. c1t0d0 SEAGATE-ST336752LC-0002 cyl 18360 alt 2 hd 8 sec 488
          /pci@1f,0/pci@1/scsi@8/sd@0,0
       1. c1t1d0 SUN36G cyl 24620 alt 2 hd 27 sec 107
          /pci@1f,0/pci@1/scsi@8/sd@1,0

Click on any of the images below for a better view. The number under the image is the size of the better view in bytes followed by the date it was last edited and its name. Click on the name to view the jpeg header. Click back in your browser to return to this index or the parent of this archive has more images too.



91K Jul 1 15:19 P6293188.jpg

72K Jul 1 15:19 P6293182.jpg

340K Jun 29 22:26 P6293202.jpg


325K Jun 29 22:25 P6293199.jpg

214K Jun 29 22:09 P6293193.jpg

377K Jun 29 18:46 P6293186.jpg


424K Jun 29 18:46 P6293185.jpg

313K Jun 29 18:45 P6293180.jpg

357K Jun 29 18:44 P6293174.jpg


376K Jun 29 18:44 P6293172.jpg

434K Jun 29 18:44 P6293170.jpg

405K Jun 29 18:43 P6293169.jpg


352K Jun 28 00:33 v120.jpg

This 338 index.shtml was served for rob.com (207.170.160.160) via (none) on Monday, 01-Jul-2002 15:39:42 EDT using Wget/1.7 last edited by rob on Monday, 01-Jul-2002 15:27:19 EDT.